Edit Game
FS
 Delete

Use commas to add multiple tags

 Private  Unlisted  Public




Delimiter between question and answer:

Tips:

  • No column headers.
  • Each line maps to a question.
  • If the delimiter is used in a question, the question should be surrounded by double quotes: "My, question","My, answer"
  • The first answer in the multiple choice question must be the correct answer.






 Save   20  Close
A pig pen measuring 1.5 m x 4.8 m is to be constructed of concrete and concrete hollow blocks (CHB). Estimate the volume of concrete for the continuous footing if the thickness is 15 cm and the width is 30 cm.
Volume = (Perimeter) (thickness x width) = [(2x4.8) + (2x1.5)] (0.15 m) (0.30 m) = 0.567 cu.m.
A board-foot of lumber is equivalent to ___________. A. 144 in^3 B. 1 cu.ft. C. a and b D. none of a and b
A. 144 in^3
If 12.5 square meters of space is needed for every 100 heads of chickens more than 4 weeks old, what should be the length of a 10 m wide poultry house to accommodate 10,000 heads of such animals?
Length= 12.5/100 : 10 (x)/10,000 = 125 m
A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine the outside diameter in mm of the tube if the stress is limited to 120 MN/m^2.
119.35 mm
aluminum rod is rigidly attached b/n a steel rod and a bronze rod. Axial loads are applied at the positions indicated. Find the max. value of P that will not exceed a stress in steel of 140 MPa,in aluminum of 90 MPa, or in bronze of 100 MPa
10,000 N or 10 kN
A wooden post with a cross-section of 200mmX100mm has a length of 2,500mm. What is the slenderness ratio?
Slenderness ratio = effective length/least radius = 2500mm/100mm = 25
Engr. X & Engr. Y were asked by Dean Santos to design 5 pcs. of benches. The engineers found out that they needed 10 pcs. of 2"x3"x12' and 6 pcs. of 2"x2"x12 for each bench. How many board feet of lumber would they need per piece of bench?
Total bd ft= [(10) (2x3x12/12)] + [(6)(2x2x12/12)] = 84 board feet
A simply supported beam has a span of ‘L’ and a uniformly distributed load of ‘w’. What is the value of the reactions at the support?
1/2 wL
An inclined or horizontal member that establishes the upper edge of a truss. This member is subjected to compressive and bending stresses. A. king post B. bottom chord C. top chord D. webs
C. Top chord
One of the most commonly used building material in many parts of the world because of its reasonable cost, ease of working, attractive appearance and adequate life if protected from moisture and insects.
Wood
Structural element that transmits, through compression, the weight of the structure above to other structural elements below. A. Truss B. Column C. Beam
B. column
A load which tends to shorten or crush a structural member. A. compression B. shear C. tension D. bending
A. compression
What force is required to punch a 20-mm-diameter hole in a plate that is 25 mm thick? The shear strength is 350 MN/m^2.
P = 350 [pi (20) (25)] = 549.8 kN
How many bd-ft is in a piece of lumber with a cross-section of 2”x4” if its length is 216 in?
bd ft = [(2 x 4) (216 x 1/12)]/12 = 12
The minimum space requirement for weaners (up to 10 kg weight) is 0.11 square meter per animal. How many pigs of this category can be confined in a 2m by 1.5m pen?
(2x1.5)/0.11=27.3 =27
Smaller members which directly support the floor or ceiling. A. Joists B. girders C. rafters D. purlins
A. Joists
The ability of a material to retain its strength and other properties over a considerable period of time. A. Durability B. Elasticity C. Toughness D. Stiffness
A. Durability
Refers to a swine with 40 to 65 kilograms in weight A. grower B. fattener C. finisher
A. grower
Sheet metal that is thicker than gauge 22. A. gauge 24 B. gauge 26 C. gauge 14 D. both a and b
C. gauge 14
Refers to the capacity of the material to resist fracture under impact loading. A. Toughness B. Hardness C. Elasticity D. Workability
A. Toughness